31. Is there any part of the compact filling and capping line that need to be pay attention more? Does the capping head wear off the cap when it is tightening? | Sold in 50 Countries High-Quality Industrial Packaging Equipment Manufacturer | Neostarpack Co., Ltd.

Neostarpack is a liquid filling packaging line supplier, good at filler, tablet counter, capping machine labeller and bottle rinser.

31. Is there any part of the compact filling and capping line that need to be pay attention more? Does the capping head wear off the cap when it is tightening?

No, under normal operation, the capping machine will not cause the cap of the bottle to wear.


The capping head of the capping machine has a rubberized design. When the machine tightens the cap, the rubber of the capping head protects the cap from abrasion. When the capper is normally tightened, it will rub against the cap. Therefore, the capping head will naturally wear out with the use time. Therefore, the capping head is one of the basic consumables of the capping machine, and it needs to be replaced according to the frequency of use and condition to maintain normal. Although the capping head is a consumable item, if the capping machine is produced in the correct manner, basically, the capping head will not be worn too quickly to be able to tighten the cap, but if the machine is used in an incorrect manner, It is possible to accelerate the damage rate of the rubber cover of the capping head, so that the machine cannot operate normally.

The following points are the conditions for the rapid wear and tear of the encapsulation caused by the improper operation of the capping machine. First, it is necessary to pay attention to:
1. When operating the capping machine, the height of the cap is adjusted too low, so that the cap is pressed too tightly, and the cap is continuously and excessively rubbed during the continuous tightening cap operation. The rubber is quickly worn and emptied by the cap. If the height of the capping head is adjusted too low at the beginning, and the rubber is worn out and hollowed out, there is no extra space to lower the height of the capping head to grip the bottle cap. When the capping head cannot tighten a part of the bottle, then you cannot continue to produce.
2. Pay attention to check if the delay time of tightening the bottle cap is too long. Usually, if the capping delay time is adjusted too long while setting the capping machine, it will be easy to have abnormal sound during production work; this part can be observed through sound. If the cap is tightened for too long, and the cap continue to tighten the cap after the cap has been tightened. At this time, the rubber is quickly worn due to excessive friction. At this time, if the cap is pressed too tightly and the capping time is too long, the abrasion of the capping head is accelerated, so that the cap is excessively worn out in a short time, and a new cap is required to be replaced, in order to carry out production again.
3. Non-standard caps: special caps or caps with fragile materials. In this case, a special cap and customized cap mechanism must be used to avoid capā€™s abrasion.
Based on the incorrect use of the above points, the capping headā€™s rubber may wear out quickly. It is recommended that while using the machine, please follow the correct operation steps of the machine manual, normal settings check and confirm, so that the consumables wonā€™t be consumed quickly. And it also reduces the chance of rapid damage to the capping head and increases the smoothness of production operations.

Photo Gallerys

31. Is there any part of the compact filling and capping line that need to be pay attention more? Does the capping head wear off the cap when it is tightening? | Sold in 50 Countries High-Quality Industrial Packaging Equipment Manufacturer | Neostarpack Co., Ltd.

Based in Taiwan since 1998, Neostarpack Co., Ltd. has been an industrial packaging machine manufacturer. Our main products, include labelers, liqiud filling machines, tablet counters, capping machines, bottle rinser machines, complete filling lines, label counters, card feeders and label dispensers, which are total packaging solutions for customers in bottling packaging machinery industry.

Neostarpack team has devoted ourselves to manufacture labeling machine, automatic filling machine, tablet capsul counter, capping machine, and other packaging machine. We offer bottle packaging solutions, help to improve production automation experience for over 20 years. We also provide professional OEM service and customized machine. We extend business domain to over than 50 countries.

As an automatic filling packaging line supplier, besides packaging labeling and capping equipment, filling and closing machine can be tailored to the specific needs of the customers and their industries. Both with advanced technology and 25 years of experience, Neostarpack ensures each customer's demands are met.